D7net Mini Sh3LL v1

 
OFF  |  cURL : OFF  |  WGET : ON  |  Perl : ON  |  Python : OFF
Directory (0755) :  /var/www/html/../../../usr/share/alsa/../doc/python3-newt/../debconf-i18n/../libdconf1/

 Home   ☍ Command   ☍ Upload File   ☍Info Server   ☍ Buat File   ☍ Mass deface   ☍ Jumping   ☍ Config   ☍ Symlink   ☍ About 

Current File : /var/www/html/../../../usr/share/alsa/../doc/python3-newt/../debconf-i18n/../libdconf1/README
dconf is a simple key/value storage system that is heavily optimised for
reading.  This makes it an ideal system for storing user preferences
(which are read 1000s of times for each time the user changes one).  It
was created with this usecase in mind.

All preferences are stored in a single large binary file.  Layering of
preferences is possible using multiple files (ie: for site defaults).
Lock-down is also supported.  The binary file for the defaults can
optionally be compiled from a set of plain text keyfiles.

dconf has a partial client/server architecture.  It uses D-Bus.  The
server is only involved in writes (and is not activated in the user
session until the user modifies a preference).  The service is
stateless and can exit freely at any time (and is therefore robust
against crashes).  The list of paths that each process is watching is
stored within the D-Bus daemon itself (as D-Bus signal match rules).

Reads are performed by direct access (via mmap) to the on-disk database
which is essentially a hashtable.  For this reason, dconf reads
typically involve zero system calls and are comparable to a hashtable
lookup in terms of speed.  Practically speaking, in simple non-layered
setups, dconf is less than 10 times slower than GHashTable.

Writes are not optimised at all.  On some file systems, dconf-service
will call fsync() for every write, which can introduce a latency of up
to 100ms.  This latency is hidden by the client libraries through a
clever "fast" mechanism that records the outstanding changes locally (so
they can be read back immediately) until the service signals that a
write has completed.

dconf mostly targets Free Software operating systems.  It will
theoretically run on Mac OS but there isn't much point to that (since
Mac OS applications want to store preferences in plist files).  It is
not possible to use dconf on Windows because of the inability to rename
over a file that's still in use (which is what the dconf-service does on
every write).

The dconf API is not particularly friendly.  Because of this and the
lack of portability, you almost certainly want to use some sort of
wrapper API around it.  The wrapper API used by Gtk+ and GNOME
applications is GSettings, which is included as part of GLib.  GSettings
has backends for Windows (using the registry) and Mac OS (using property
lists) as well as its dconf backend and is the proper API to use for
graphical applications.

dconf itself attempts to maintain a rather low profile with respect to
dependencies.  For the most part, there is only a dependency on GLib.

With the exception of the bin/ directory, dconf is written in C using
libglib.  This is a very strong dependency due to the fact that dconf's
type system is GVariant.

The dconf-service has a dependency on libgio, as do the client libraries
that make use of GDBus (and the utilities that make use of those
libraries).

The standard client library is libdconf (in client/).  If you can't use
GSettings then you should probably want to use this next.

There is also a libdbus-1 based library.  It does not depend on libgio,
but still depends on libglib.  It is not recommended to use this library
unless you have a legacy dependency on libdbus-1 (such as in Qt
applications).

Installing dconf follows the typical meson dance:

  meson builddir
  ninja -C builddir
  ninja -C builddir install

If you plan to contribute to dconf, please see the HACKING file.

AnonSec - 2021 | Recode By D7net